No water on a freezing morning usually means ice somewhere between the well and your tap. It might be the pipe, the pressure tank, the pressure switch, or the pump itself. This page covers what to do in the first few minutes, how to tell what froze, how to thaw it safely, and when to call someone.
Do these first
- 1Turn off the pump at the breaker if you smell burning, hear it humming or running with no water coming out, or can't tell what is going on. A pump running dry or against ice can burn out.
- 2Open one faucet, ideally the one closest to the tank, so thawing water and pressure have somewhere to go.
- 3Look for a split pipe. If you see water spraying or pooling, shut off the main valve at the tank and call a plumber or well pro before you power the pump back on.
- 4Never use a torch, propane heater, or any open flame to thaw a pipe, a pressure tank, or the wellhead. It starts fires, and it can ruin plastic pipe and wiring.
- 5Keep the pump off until you know the pipes and tank have thawed. Turning it on over a frozen line can crack fittings.
What probably froze
Where the water stops tells you where to look. Check these in order.
- •Lights are on, pump is silent, no water. Check the breaker first. If it hasn't tripped, the pressure switch or the pump may be frozen or failed.
- •Pump hums or clicks but no water. Ice may be blocking the line, or the pump motor may be stuck. Turn it off and don't keep cycling it.
- •Water sputters, then stops. Often a partly frozen line between the well and the house, or a frozen pipe near an exterior wall, crawl space, or unheated pump house.
- •Only some faucets are dead. That points to a frozen pipe inside the house, not the well. Start with pipes on outside walls and in unheated spaces.
- •Pressure gauge reads zero. The tank has no water pressure behind it. Either the pump isn't running or the line feeding the tank is frozen.
If the symptoms don't match, or the pump is fine and the well just seems empty, read our guide on no water from your well. Pump trouble that isn't cold-related is covered in well pump problems.
How to thaw it safely
Go slowly. Heat the pipe gently and keep a faucet open so the water has an exit as it melts.
- 1Open the nearest faucet, then start warming the pipe at the faucet end and work back toward the frozen spot.
- 2Use a hair dryer, a heat lamp set well back, a heating pad, or towels soaked in warm water. A small space heater can warm an enclosed pump house, but keep it away from anything that burns and never leave it running unattended.
- 3Keep every electrical cord and heat source dry and away from standing water.
- 4When water starts to run, leave the faucet open for a few minutes, then check pipes and fittings for leaks before turning the pump back on.
Don't try to thaw anything down inside the well casing, and don't pull the pump yourself. Those jobs belong to a licensed pro.
If the power is out too
A well pump needs electricity, so an outage in a cold snap means no water and no heat for the pump house at the same time.
- •Open a faucet or two and let the pipes drain a bit if the house will sit without heat for a long stretch. Moving water is harder to freeze, and an emptied line can't split.
- •If you use a generator, run it outside, well away from doors, windows, and the garage. Exhaust carries carbon monoxide.
- •Have an electrician connect a generator to the pump properly. Don't plug it into a wall outlet to power the whole house.
- •When power returns, give the pipes time to thaw before turning the pump back on, and check for leaks first.
When to call a local pro
- •The pump hums, clicks, or trips the breaker after you have thawed the lines.
- •The pressure tank, pressure switch, or wellhead is cracked or leaking.
- •A buried line between the well and the house is frozen, since you can't reach it safely.
- •Water is spraying or flooding anywhere.
- •You thawed it and it froze again overnight.
- •You are not sure what froze and don't want to guess with a pump that is costly to replace.
When you call, tell them what you saw: whether the pump runs or hums, what the pressure gauge shows, which faucets work, and whether the power was out. It helps them decide if this is a thaw, a pump repair, or a bigger job. Use the quote box below to reach local drillers and pump companies who handle winter calls.
Keeping it from happening again
Most freeze-ups come from a weak spot you can fix once the weather warms up. These are worth doing before the next cold snap.
- •Heat the pump house or well pit with a thermostat controlled heater made for the job, or a heat lamp on a proper fixture. Make sure the building is sealed against drafts.
- •Use heat tape or heat cable made for water pipes on exposed lines, and follow the maker's directions. Wrong tape or a bad installation is a fire risk.
- •Insulate pipes and the pressure tank in crawl spaces, garages, and along outside walls.
- •Let a tap drip on the coldest nights if you have lines that have frozen before.
- •Know where your main valve and breaker are, so you can shut things off fast.
- •Have the system checked in the fall. A pro can look at the wellhead, pressure switch, tank, and wiring before the cold arrives. Our guide to choosing a driller lists what to ask.
FAQ
My well pump is frozen. What should I do first?▾
Turn the pump off at the breaker if it hums, runs with no water, or you are not sure what is wrong. Open a faucet, look for split pipes, and never use a torch or open flame. Thaw slowly with a hair dryer or warm towels starting at the faucet end.
How do I thaw frozen well pipes?▾
Keep a faucet open and warm the pipe gently, working from the faucet back toward the frozen spot. A hair dryer, a heat lamp set back from the pipe, or warm towels all work. Check for leaks before you turn the pump back on.
Can a frozen well pump be repaired?▾
Sometimes the pump is fine and only a pipe, the pressure switch, or the tank froze. A pump that hums, clicks, or trips the breaker after thawing may need repair or replacement by a licensed pro.
What if my well water is frozen and the power is out?▾
The pump cannot run without electricity. Keep a faucet or two open if the house will sit unheated, run any generator outside and away from the house, and have an electrician connect it to the pump. Let pipes thaw and check for leaks before restarting the pump.
How do I keep my well from freezing?▾
Heat the pump house or well pit, put heat cable made for water pipes on exposed lines, insulate pipes and the tank, and let a tap drip on the coldest nights. Having a pro check the system in the fall helps too.
Still no water after thawing?
Tell local pros what froze, whether the pump hums or runs, what the pressure gauge shows, and whether the power was out. That helps them quote a thaw, a pump repair, or something bigger.
